Every pool owner should be able to operate a manual vacuum. While the automatic pool cleaner offers an easy-to-use pool cleaning system, however, it can’t aid in vacuuming algae-filled water or cloudy water.
This is our complete, detailed guide on cleaning your above-ground or inground pool efficiently and quickly to return to enjoying your swim.
What Do You Need for Pool Vacuuming?
- Vacuum plate or skim vac (optional should you choose to use the Skimmer basket).
- The pool vacuum head.
- A pool vacuum hose is long enough to cover every section of your swimming pool.
- Telescopic pole for attachment to the head of the vac.
1. Attach Vacuum Head and Pipe to Telescopic Pole
The first step is to ensure that the pump is working. Connect the vacuum head to the top of the Telescopic stick. You can connect the vacuum head to the other edge of the flexible pipe. To ensure that the hose stays in place if it’s slippery, connect one end to the vac.
2. To Eliminate Air, Fill the Vacuum Hose With Water
The pole telescopic and the vacuum hose must be placed inside the pool. The vacuum hose’s other end should be placed against the return jets.
This forces water to flow through the hose and air out.
Make sure that the pump shuts off the vacuum outlet. There is a risk of debris and particles getting block into the pump. This could cause irreparable damage to the entire effort you put into it.
Be aware that air bubbles can appear out of the vacuum head and fall onto the surface of your swimming pool. The air will escape from the hose when the bubbles are gone.
3. Connect a Vacuum Line to the Skimmer of the Pool
Attach the skim-vac plate onto the end that you had previously placed in the direction of the returning Jet, and then close the opening using your hands before transferring it onto the Skimmer.
Place it inside the Skimmer of the basket and cover the lid. If not, suction could be removed.
Suppose you’re not using the vacuum plate to take out the Skimmer basket. Stop the end of your water-filled hose by using your hands.
Then, you can insert the pipe into the inlet of your Skimmer.
You can select any method to create suction.
As a result, for restoring vacuum suction, repeat the steps that were mentioned earlier.
4. Start Vacuuming
After you’ve constructed an effective siphon with your filter system, it’s time to sweep the pool floor. Begin at the bottom (if there is one) and work your way towards the deeper end, which is the end of your pool. In the case of a circular pool, you can start from one end and then move either left or right across the floor.
Use slow, long sweep strokes to clear. Ensure that your strokes are over cover slightly to ensure that you do not leave any debris in the dust. Rushing is just a way to kick up debris, which can reduce visibility and may take a long time to settle again.
If the water becomes cloudy, allow it some time to settle, and then vacuum once more, repeating the process until it is no longer necessary.
Hence, if the vacuum head gets stuck, turn off the machine for about a moment to stop the vacuum force, then set the vac head free.
Also, make sure you check the pressure gauge while you vacuum. If the pressure increases above what is suggest by the company, you should take a break and then backwash your Filter.
5. Remove the Vacuum and Perform the Final Clean
After you’ve vacuumed the entire pool, it’s time to tidy up and return to your pool.
- Take the vacuum head off the telescoping pole and empty any remaining water within the hose. Attach the cleaner brush onto the pole and use it to clean away any dirt, algae, and other debris that has accumulated on the sides of the pool.
- Clean any debris from the basket of your pump strainer, backwash the Filter if you have a multiport valve, and employ “Filter” settings. This is our complete guide to cleaning your Filter after vacuuming.
- If you have used the “Waste” option to clean the pool, ensure that you change the valve in “Filter. “Filter” option and continue replenishing the water in the pool until the level reimpose.
- After you’ve added water, check your water and then adjust your alkalinity level, pH, and chlorine as needed.
- Cleanse your equipment thoroughly with fresh water, dry and store it. This will maintain it in top operating condition and prevent unnecessary corrosion and wear.
It’s not necessary to fear the vacuum head! If it’s time to clean your pool, whether you’re an active person or fighting a battle against algae, you can complete the task by hand with a bit of preparation, lots of elbow grease, and plenty of patience.
Most Frequently Asked Questions About Vacuuming the Pool
Need help with your pool vacuum cleaner? Here are some frequently asked questions and their answers.
The basket skimmer is in place while vacuuming with the skim vac plate. If not, take out the skimmer basket before attaching your vacuum pipe to the inlet of the Skimmer or, in the case of an air plate. The skimmer basket can hinder your flow and make it difficult to get adequate suction.
A manual vacuum must be used at the rate it needs to clear any visible dirt and debris on the bottom and sides of the swimming pool, according to Genco Pools & Spas. A small and maintained pool normally takes between 20 and 30 minutes. If you have a dirty, small pool or a well-maintained larger pool, it could take up to 45 minutes.
Start the cleaning process by cleaning the pool's walls to eliminate algae, dirt, and other debris, focusing on the water line. You should perform this task the night before cleaning the pool for the best results. The resulting debris will sink to the bottom of your pool, where it will be swept away later.
If you have vacuumed up trash, you'll require turning your Filter on to the rinse setting. Then, turn on the pump, and permit it to run for approximately 30 seconds. After that, shut off the pump. Make sure you change your Filter's setting to filter following this.
This is because the Filter isn't strong enough to eliminate debris rapidly. If you're facing many fine particles going over your system, change the Filter's setting to Waste and bypass the Filter completely as you Vacuum. Be sure to fill your pool with clean water while you vacuum to ensure that the water level within your pool doesn't become too low. Do you put a skimmer basket inside when you vacuum your pool?
How long will it take to clean an entire swimming pool?
Do we need to brush the pool before vacuuming?
What setting should your pool's pump be set to when it comes to vacuuming?
The dirt returns to my pool when we vacuum it; why?
